Battery Saver Kit for Rechargeable Lithium and SLA Batteries
Battery Saver Kit for Rechargeable Lithium and SLA Batteries
- CAT.NO: KC5523
1/2
In-Store Only
$12.20$33.90
Save $21.70
Deliver to
Add postcode for delivery availability
Store
Choose a store for stock availability
Battery Saver Kit for Rechargeable Lithium and SLA Batteries
$12.20
Battery Saver Kit for Rechargeable Lithium and SLA Batteries
Refer: Silicon Chip Magazine September 2013
This tiny circuit fits in between the battery and load and cuts off the power when the battery becomes flat to prevent the battery over-discharging and becoming damaged. Suitable for use with cordless power tools, emergency lights, small to medium UPS (up to about 300VA) and a wide variety of other devices.
• Suits most SLA, Li-ion, Li-Po and LiFePO4 batteries between 6 to 24V
• Uses very little power (* Handles 20A continuous, 30A peak (Charge or discharge)
• Cut-off voltage adjustable from 5.25 to 25.5V
• 0.3 - 2V hysteresis, depending on battery type and voltage
• Small PCB to fit in small spaces (38 x 18.5mm)
• Battery can be recharged once cut-out has engaged (maximum 1.5A)
There is also provision for connecting an LED or external buzzer (not included)
Supplied with double sided, soldermasked and screen-printed PCB with SMDs pre-soldered*, voltage setting diodes and resistors, and components.
PCB size: 34 x 18.5mm
*Note: We've pre-soldered all of the surface mount components to save you time and frustration, apart from the three voltage setting resistors.
Refer: Silicon Chip Magazine September 2013
This tiny circuit fits in between the battery and load and cuts off the power when the battery becomes flat to prevent the battery over-discharging and becoming damaged. Suitable for use with cordless power tools, emergency lights, small to medium UPS (up to about 300VA) and a wide variety of other devices.
• Suits most SLA, Li-ion, Li-Po and LiFePO4 batteries between 6 to 24V
• Uses very little power (* Handles 20A continuous, 30A peak (Charge or discharge)
• Cut-off voltage adjustable from 5.25 to 25.5V
• 0.3 - 2V hysteresis, depending on battery type and voltage
• Small PCB to fit in small spaces (38 x 18.5mm)
• Battery can be recharged once cut-out has engaged (maximum 1.5A)
There is also provision for connecting an LED or external buzzer (not included)
Supplied with double sided, soldermasked and screen-printed PCB with SMDs pre-soldered*, voltage setting diodes and resistors, and components.
PCB size: 34 x 18.5mm
*Note: We've pre-soldered all of the surface mount components to save you time and frustration, apart from the three voltage setting resistors.
Kit
Kit Form
Short Form (circuit only)
Tools required
Soldering Iron,Flat Head Screwdriver
Estimated Construction Time
60.0 min
Difficulty
Detailed
Application Field
Battery Saver Kit for Rechargeable Lithium and SLA Batteries
PCB Width
18.0 mm
PCB Length
34.0 mm
Packaged Dimensions
Packaged Dimensions
20.0cm(Length) x 10.0cm(Width) x 4.0cm(Height)
Discover more
Transmitter Kit for KC-5473
CAT.NO: KC5474
$18.90
Available for delivery
AVR Adaptor Board for KC-5340 Kit Back Catalogue
CAT.NO: KC5421
$28.90
Available for delivery
Temperature Switch Kit B048
CAT.NO: KG9140
$29.90
Available for delivery
Raucous Alarm Kit Back Catalogue
CAT.NO: KC5327
$28.90
Not Available for delivery