text.skipToContent text.skipToNavigation

COVID-19 & Shipping Updates

In line with government guidelines, all Jaycar company-owned stores are open to all customers. We encourage all customers to take advantage of free delivery for online orders over $99. We thank you for your support as we continue try to keep our community and stores safe. See here for the latest on delivery delays.

12/24V 10A Solar Charge Controller with USB 12/24V 10A Solar Charge Controller with USB MP3750 45.90 In stock

12/24V 10A Solar Charge Controller with USB

CAT.NO:MP3750

12/24V 10A Solar Charge Controller with USB

CAT.NO:  MP3750

Pulse Width Modulation (PWM) to control battery charging.
Add to wishlist

In Stock Notification:

You'll be notified as soon as this item is back IN STOCK

or Cancel

Unsubscribe from this in stock notification

or Cancel

Special Notification:

You'll be notified as soon as this item is on special

or Cancel

Unsubscribe from this on special notification

or Cancel

Notify me when on special
	
$45.90
Bulk Pricing:
1-1 $45.90
2-3 $40.90
4+ $35.90
In Stock



Description
1 Year Warranty
USB 2.0

Intelligent yet lightweight, this solar controller uses Pulse Width Modulation (PWM) to control battery charging. With total autonomy, its set-and-forget operation means you can get maximum charge into your batteries from your solar installation without having to worry about those things. It provides all the important safety features such as overload, short-circuit, over-discharge, and reverse-polarity protection. A handy feature is also the USB port located on the front panel, to provide up to 1.2A charging. Very handy during power outages to keep your phone charged without any additional equipment. Charge modes include bulk, equalise, and float charging, and the unit automatically switches to the best charging mode. Suitable for sealed led acid, as well as Gel/flooded type cells.

Features:
- Automatic charge mode selection
- Suitable for 12V and 24V battery banks
- USB charging port on front panel
- Charging Modes: Bulk, Equalise, Float
- Supports: Sealed, Gel and Flooded
- USB Output: 5V @ 1.2A

 

 


Handy Tip Solar Charge Controllers

Directly connecting a solar panel or array to a battery can be catastrophic as solar panels can output a wide voltage range. As an example, a nominal 12 volt rated panel can output anything up to 22volts during an average sunny day. A solar charge controller between the panel and the battery ensures the battery receives the correct output voltage and current from the panel to minimise the risk of the battery being overcharged or discharging back into the panels. Charge controllers come in a variety of types which give different performance and can be matched to simple recreational applications all the way up to complex high power solar array installations.

SWITCHING: Simple switching controllers connect the panel to the battery when the panel is providing power & the battery is not fully charged. This type of controller is low cost and only good for basic solar equipment setups such as standby lighting, etc. where the panel yield is far higher than the load requires. PWM: Pulse width modulated (PWM) controllers continually apply voltage pulses to the battery whenever the panel is providing sufficient voltage. The pulse width (or duration) is varied by the controller depending on the charge state of the battery to ensure the correct amount of charge is harvested from the panel whenever it is available. As a result, PWMc ontrollers provide a much higher power yield than simple switching controllers.

MPPT: Maximum power point tracking (MPPT) controllers maximize power conversion between the panel output and the battery input by using a DC to DC switchmode power converter. By continuously tracking the panel output and adjusting the converter they yield the maximum amount of power under widely varying solar conditions. MPPT controllers give the best solar system efficiency and improve solar system power yield by a significant percentage. Both PWM and MPPT controllers are available with display panels which allow you to track performance of the solar system. Panel voltage, battery voltage, charging current, and total charge supplied can be easily displayed so you can ensure the system is running correctly. More complex models also include integration functions to remotely control other equipment or be linked into advanced systems.

Specifications
Solar Charge Controllers and Regulators

Max Solar Panel Array 120W-240W
Max PV Open Circuit Voltage 50V
Max Charging Current 10A
Max Load Current 10A
Charge Controller Technology Pulse Width Modulated (PWM)
DC Current Rating

DC current rating 10A
DC Voltage Rating

DC Voltage 12V,24V
Product Dimensions

Length 120mm
Weight 100g
Width 67mm
Height 22mm
Included USB Charge Output

Total Current Rating 1.2A
Number of Ports 1pc
Low Voltage Power / Vehicle Adaptors

Input Type Screw Terminal
Output Type Screw Terminal
Ingress Protection Rating

IP Rating IP20
Dust/Particle Ingress Protection 2 - Objects > 12.5mm, Fingers or small objects
Liquid/Moisture Ingress Protection 0 - Not protected
Operating Temperature

Operating Temperature -35°C-55°C
Warranty: 12 Months
Downloads
Articles


DELIVERY

✔ In Stock

Out of Stock

Low Stock

Standard Freight: 2-3 days for most areas in the North Island and 3-5 for the South Island
 

CHECK IN-STORE