Speed Control Kit for Induction Motors
- CAT.NO: KC5509
1/2
Discontinued
$14.39$339.00
Save $324.61
Deliver to
Add postcode for delivery availability
Store
Choose a store for stock availability
Speed Control Kit for Induction Motors
$14.39
Refer: Silicon Chip Magazine April/May 2012 (Revisions SC Aug 2013)
Control induction motors* up to 1.5kW (2HP) to run machinery at different speeds or controlling a pool pump to save money. Also works with 3-phase motors. Full form kit includes case, double-sided silk-screened PCB, heatsink, cooling fan, hardware and electronics (including parts from revised article in August 2013).
Features
Controls single-phase or 3-phase induction motors
Runs from a single-phase 230VAC, 10A power point
Over-current, over-temperature, under-voltage, over-voltage and short-circuit protection
EMI (electromagnetic interference) filtering for reduced radio interference
Inrush current limiting
Isolated control circuitry for safety
Mounted in an IP65 sealed enclosure
Adjustable speed ramp up/down
Pool pump mode
Can run 3-phase motors in either direction
Optional external speed control pot with run, reverse and emergency stop switches
Motor run/ramping and reverse indicator LEDs
Fault indicator LED
Open collector output provides either fault or up-to-speed indication
Specifications:
Motor power: up to 1.5kW (2 horsepower)
Maximum output voltage (single or 3-phase motor): ~230V RMS
Continuous output current: 8.5A RMS (single-phase), 5A RMS (3-phase)
Short term overload current: 13A RMS (single-phase), 7.5A RMS (3-phase)
Switching frequency: 16kHZ * Quiescent power: 28W
Speed ramp period adjustment: 3-30s to full speed
Continuous input current: up to 8.7A RMS
Speed control range: 1-100% or 1-150% (0.5Hz or 75Hz) in 0.05Hz steps
Efficiency: Up to 96%
Speed control signal: 0-3.3V
Up-to-speed/fault output sink: 12V/200mA
IMPORTANT NOTES:
This is an advanced project for an experienced constructor
*Project does not work for motors with centrifugal switch
More information:
More information can be found on the Silicon Chip website. The article can be dowloaded for a small fee. http://www.siliconchip.com.au/Issue/2012/April/1.5kW+Induction+Motor+Speed+Controller%2C+Pt.1
Control induction motors* up to 1.5kW (2HP) to run machinery at different speeds or controlling a pool pump to save money. Also works with 3-phase motors. Full form kit includes case, double-sided silk-screened PCB, heatsink, cooling fan, hardware and electronics (including parts from revised article in August 2013).
Features
Controls single-phase or 3-phase induction motors
Runs from a single-phase 230VAC, 10A power point
Over-current, over-temperature, under-voltage, over-voltage and short-circuit protection
EMI (electromagnetic interference) filtering for reduced radio interference
Inrush current limiting
Isolated control circuitry for safety
Mounted in an IP65 sealed enclosure
Adjustable speed ramp up/down
Pool pump mode
Can run 3-phase motors in either direction
Optional external speed control pot with run, reverse and emergency stop switches
Motor run/ramping and reverse indicator LEDs
Fault indicator LED
Open collector output provides either fault or up-to-speed indication
Specifications:
Motor power: up to 1.5kW (2 horsepower)
Maximum output voltage (single or 3-phase motor): ~230V RMS
Continuous output current: 8.5A RMS (single-phase), 5A RMS (3-phase)
Short term overload current: 13A RMS (single-phase), 7.5A RMS (3-phase)
Switching frequency: 16kHZ * Quiescent power: 28W
Speed ramp period adjustment: 3-30s to full speed
Continuous input current: up to 8.7A RMS
Speed control range: 1-100% or 1-150% (0.5Hz or 75Hz) in 0.05Hz steps
Efficiency: Up to 96%
Speed control signal: 0-3.3V
Up-to-speed/fault output sink: 12V/200mA
IMPORTANT NOTES:
This is an advanced project for an experienced constructor
*Project does not work for motors with centrifugal switch
More information:
More information can be found on the Silicon Chip website. The article can be dowloaded for a small fee. http://www.siliconchip.com.au/Issue/2012/April/1.5kW+Induction+Motor+Speed+Controller%2C+Pt.1
Kit
Kit Form
Full Form (circuit and enclosure)
Tools required
Flat Head Screwdriver,Soldering Iron
Estimated Construction Time
4.0 hr
Difficulty
Complex
Application Field
Speed Control Kit for Induction Motors
Kit Group
General Projects
Packaged Dimensions
Packaged Dimensions
25.0cm(Length) x 20.0cm(Width) x 13.0cm(Height)
Discover more
PC Link for Automatic Control Kit
CAT.NO: KV3590
$10.30$83.90
Save $73.60
Not Available for delivery